IRFP datasheet, IRFP pdf, IRFP data sheet, datasheet, data sheet, pdf , International Rectifier, V Single N-Channel HEXFET Power MOSFET in a. The IRFP and IRFP are advanced power MOSFETs designed, tested, and guaranteed to withstand a specified level of energy in the breakdown. IRFP, SiHFP Vishay Siliconix. FEATURES. • Dynamic dV/dt Rated. • Repetitive Avalanche Rated. • Isolated Central Mounting Hole. • Fast Switching.

Author: Tule Tojakree
Country: Malta
Language: English (Spanish)
Genre: Video
Published (Last): 17 July 2005
Pages: 444
PDF File Size: 8.30 Mb
ePub File Size: 4.17 Mb
ISBN: 497-7-43017-940-6
Downloads: 38560
Price: Free* [*Free Regsitration Required]
Uploader: JoJohn

Hello, I want to drive a V led strip using the IRFP mosfet for driving from an arduino pin I irpf360 a 4n25 irfp360 datasheet like the schematic attached. In a circuit like this with a weak datasheet and an incredibly massive gate chargeyou’ll be lucky to succeed at 1kHz. T3sl4co1l Super Contributor Posts: The flickering is probably the result of the PWM irfp360 datasheet beeing modulated by the mains frequency. The LED string will see the same maximum voltage with or without a capacitor.

What is the “8. I think people get into as much trouble with high speed drivers as they intend to solve.

DATASHEET IRFP3306PBF – International Rectifier MOSFET N To-247ac

I tried running the optocoupler from a irfp360 datasheet and same results. Greek letter ‘Psi’ not Pounds per Square Inch. You can use irfp360 datasheet opto coupler like 6N I measured the dc voltage on the strip without and whit caps and there was a almost 50v difference if I recall right.

Seekonk Super Contributor Posts: Using a 6N and a MCP is the correct way to drive the mosfet, irfp360 datasheet using several kHz for driving a large led strip is not good and not necessary unless you add an inductor for smoothing the current.


There is no need for the ohm which just reduces your drive. The average current will increase because of the old “area under the irfp360 datasheet.

If this is for dimming, you should use an even steeper ratio. What significance is the irfp360 datasheet Please login or register.

Life without Arduino still exist. Check the pic again, He’s using 8. I have no trouble switching with opto isolators. In software I always eliminate irfp360 datasheet pulses at either end which only cause heating. There was an error while thanking.

403 Forbidden

I’m assuming you’re irfp360 datasheet a Irfp360 datasheet light here. Where is the 8. Single transistor optoisolators, like 4N25, aren’t capable of switching much faster than a microsecond, suggesting a frequency below 50kHz. What is the light string? There are very simple dimmers on internet.

To simplify the layout, irf3p60 are also optocoupler gate driver ICs which contain both in one package. The 4N25 is an analog optocoupler and is definitely datasheett of magnitude too slow. Drop me a message! I made a test setup like the img attached without c1 it was very unstable.

Thank you for the reply, by light string I irfp360 datasheet an V led strip in the irfp datasheet I understood that iffp360 vgs is 10V the purpose dataasheet for dimming the led strip I use a rectifier bridge so the led strip is powered with DC could you recommend a logic level mosfet that can handle more than V dc and more than 10A irfp360 datasheet.

Can’t be that hard to find a 48V or so wall wart, that is a lot of voltage to switch fast. Try irfp360 datasheet a capacitor after the rectifier to get a better dc voltage.

Vishay Archives – Page 7 of 94 – Direct Components

Nothing is quite like a great datashheet power-station. I am using the pwm from the atmega, the default hz is too small I would like hz or hz I dayasheet thinking the optocoupler cannot handle the switching and consider using a 6n is the 4n25 suited for this application or should I use something else?


I think you would be better playing with lower voltages. It may not be easy finding a logic level FET capable irfp360 datasheet V and 10A as requested, what is the current consumption of the irfp360 datasheet strip when fully on?

I have considered the 12v led strip option, but the price would krfp360 much higher, for 12v I would need a supply at each 5 m and much more amps to drive. Another option would irfp360 datasheet to use a phase controlled triac irfp360 datasheet MOC optocoupler.

Which I’m guessing is your problem? Use a logic level mosfetreason being normal type mosfet cannot be fully turned on by microprocessor output resulting in high resistance and heat built up in mosfet that’s why your circuit failed. Dwtasheet irfp360 datasheet does it serve? For irfp360 datasheet, if I recall even the 6N should be fast enough for this ratasheet, and can handle higher voltages than the 6N if 7V is too low for driving the irfp360 datasheet of the FET.

Performa01 Frequent Contributor Posts: Like to see a little irfp360 datasheet drive voltage to fully turn on the FET. Did you miss your activation email?